3DHealthStore - Transcutaneous Electrical Nerve Stimulator HT-326

Health & Beauty

Categories

Tens Electrode and Wire

TENS Unit

UltrasoundProfessional

Book and Medicine

Cards We Accept

Home » Medical and Health » EMS Unit » HT-326L4

LCD Digital EMSHT-326L4
[HT-326L4]

List Price: ~~$155.00 USD~~
Our Price: $139.00 USD
You Save: 10% or $16.00 USD
US & Canada Shipping cost: $24.50 USD

Preparation for use

The buttons on the left control left channel(CH1,2) output the buttons on the right control right channel (CH3,4) output.
If the user wishes to use only one output, make sure you operate the buttons on the same side of output in use. If user wishes to use four outputs, make sure your program both sides.
1. Press right or left"ON" button to turn on the unit both "density" and "mode" will begin to flash.
2. Use "ON" and "OFF" buttons to raise or lower the density level to users choice. When density is at "0" the down / off button will close the units. When unit is turned on, program 1 will automatically be displayed. Raising the density level will start this program.
3. The program can be changed at anytime by pressing the "select" button again. If progra has not been selected within 10 seconds unit will auto returen to program that was being used.
  Program 10 will be show as "PO", it is fully adjustable.
4. When the program as been changed. The density level will return to"0" see step 2.
5. When PO has been selected, the "on time" and "off time" will begin to flash.
6. Use right/left buttons to change the "off time" / "on time". Up and Down buttons will raise and lower the "ON" and "OFF" times. When "ON" and "OFF" times have been selected, press enter to set them. When this has been down "rate" will begin to flash.
  When programming "rate" and "timer", both left or right buttons can be used.
7. Select rate for use by pressing the "Up" and "Down" buttons. To set, press "enter" and "timer" will begin to flash.
8. Select time (timer) by pressing the "Up" and "Down" buttons. To set, press "enter' and "density" will begin to flash.
9. To change density, see step 2.
  - If the "enter" buttons is pressed twice after following steps 5-9, the unit will returen to the beginning, as in step1
  - When timer has reached 0 min. Unit will automatically shut down.
  - In order to turn off unit, BOTH density levels must be at "0". Then Off / Down button will close the unit.
  - If both density levels are at "0" and unit is not being used, it will automatically shut down after 3 mins
  - P1-P9 timer is programmed 30 mins. If you want to change another time, please press "enter" button and both left / right buttons.
  - The LCD will exchange display "density" , "mode", "timer", "rate" (p1-P9) or "density" "on time" "off time" "rate" every 3 seconds.

EMS HT-326LT Technical Specification:

Channels	Four independent channels
Power Source	9 V battery
Channels Isolation	92 independent isolated transformer
Density	Change of 16 steps pulse amplitude
Output Current	100 mA(10 steps) peak to peak current into 500 ohm load
Timer	30 or 01~99 minutes backward count
Mode	Program P1-P5 massager, P6-P9 EMS the final P0 fully adjustable program
Dimensions	170 x 132 x 24mm
Wave Form	Dual phases square wave
Pulse Width	250 microsecond
Ramp UP	3 seconds
LCD Display	Timer / Mode / On Time / Rate / Off Time / Density
Output Load Detect	Alarm in operation without connect lead wire
Buzzer	3 different reminders: 1.corrent single beep, 2. pay attention triple beep , 3 mistake continue beep

[<<Prev] 1 2

Current no reviews for this product

Write a new review >>

Advance Search

Shopping Cart

0 items

Your Account

Your Email Address

Your Password

Best Sellers

01.	EMS 7000 (TX-1311)
02.	LCD Digital EMSHT-326L4
03.	LCD Digital Multi-Channel EMS
04.	EMS 6500
05.	Prom-550 DIGITAL EMS UNIT

Information

Ordering Info
About Us
Privacy
Pricing Policy
Return Policy
What is ISO13488
Shipping Info
FAQ
Herbal Safety Guidelines
INFRARED JADE MATTRESS CONTROL PANEL
HOW TO USE THE SILVER MATTRESS
Links
Contact Us
Site Map
Vendor